試驗機在日常操作使用中要注意一些事項，可以更好的保養好，延長使用壽命，下面與大家分享液壓萬能試驗機的日常維護事項，

Testing machine should pay attention to some issues in daily operation,can better maintenance, prolong the service life, the share of hydraulic universal testing machine daily maintenance matters with you,

1.試驗機各部分應經常擦拭干凈，對沒有噴漆的表面擦拭干凈后應用棉紗沾少量的機油再擦一遍，以防止生銹，

The 1 test machine should always wipe clean, the application of no paintsurface wipe clean after cotton dip a small amount of oil and then wipe it again, to prevent rusting,

雨季期間更應注意擦拭，不用時用防塵罩罩住以防塵土侵入。

During the rainy season should pay attention to cleaning, when not in use and dust cover to prevent dust intrusion.

2.控制柜上所有活門不應打開放置，以免塵土進入內部，影響測量機構的靈敏性易造成短路老化。

2 control cabinet all valve should not be open place, so as to avoid dust entering the inner, sensitivity measurement mechanism caused by short circuit aging effect.

3.長期頻繁使用可能導致油量減少或變質，應當根據使用情況每隔1-3個月檢查一次油量。本設備停止運行15分鐘后，觀察油窗，

3 may lead to reduce the amount of oil or deterioration frequently used for a long time, should according to the use of every check 1-3 months of the first oil. This equipment is stopped after 15 minutes, to observe the oilwindow,

如油面低于油窗則添加同種液壓油至油窗中間位置；如油已變質，須換上新的液壓油。

If the oil level is lower than the oil window is added to the sameintermediate position of the hydraulic oil to the oil window; if the oil has been deterioration, must put on new hydraulic fluid.

4.頻繁使用本設備做拉伸破斷試驗可能導致部分緊固件松動。

4 the frequent use of the equipment to do the tensile breaking test may lead to some loose fasteners.

5.根據環境條件和使用頻度，每3-6個月對以下部位進行潤滑：

5 according to the environmental conditions and the frequency of use,every 3-6 months for the lubrication of the following parts:

6.上橫梁和移動橫梁上各有2只裝置鉗口用的鉗口卡板，是本機的重要零件，應當根據使用情況經常清除鉗口卡板與橫梁接觸面上的雜物，以免拉毛接觸面。方法是：拆移動橫梁一側的壓板，取出鉗口卡板，用油抹布分別將鉗口卡板和橫梁的接觸面清除干凈，涂上適量黃油與石墨的混合油脂，裝回鉗口卡板后擰緊壓板的固定螺 絲。

6 beam and the moving beam on each jaw clamping device with 2 jaws, is an important part of the machine, should according to the use of often remove jaw clamping plates and the crossbeam on contact surfacedebris, so as to avoid rough contact surface. Method: remove the sideplate is moving crossbeam, remove the jaw clamp, oil cloth respectivelycontact surface of the jaw plate and beam clean, coated with an appropriate amount of butter and graphite mixed fat, fixed screwtightening clamp jaw clamping back after.

液壓萬能試驗機:http://m.mysdfhsj.com